On July 7th, 2017 I went in for what was supposed to be a minor surgery. I was diagnosed with a non-cancerous cyst, which is quite common except for it was located right on top of my tailbone (not on the tailbone but right next to it). This meant that I was regularly sitting on it, especially when I would slouch.
It had originally come up 3 or 4 years ago after 6 months of karting all the time. I thought it was just a result of all that trauma to my tailbone. It was an annoyance but never very painful until this past June, during the second Portland International Raceways weekend. After the first day of testing, I woke up sore all over my body and my cyst was really tender.
I ignored all the pain and discomfort and made it through the weekend but went to the doctor the following week. It turned out that my cyst had gotten so swollen, it was infected and those body aches, were my body fighting the infection.
Long story short, I needed surgery to have it completely removed. It is a straight-forward procedure and usually within a week, someone can go back to normal activities, but because of the location, the recovery was at least 2 weeks and possibly up to 2 months before feeling ‘normal’ again. Well for me, it ended up being the 2 months.
A week after the Pacific race, I was reading to my kiddo and his friend, but I was also laid up, trying to take the load off my incision.
The next couple of weeks were really tough. I don’t know how differently or faster things would have healed if I had not raced but I think it slowed things down. A checkup with the surgeon a couple weeks later showed everything looked good but she was surprised to hear that I was in so much pain.
I headed her advice and just tried to rest up, sprinkling in some yoga and days of more walking. 1.5 months after the surgery was the August 19-20 Dash for Kids race, back at Portland International Raceways.
Our setup at Portland International Raceways
= Sub-Par Performance
During the race weekend, we decided to hit the ‘reset’ button on our suspension setup, seeking coaching and advice from the 2016 PRO3 Champion, Olivier Henrichot (a future post on that experience). We made dramatic changes to the setup, where in the end, I was able to hit the same lap times as before, with less of an effort and more confidence in feedback from the car.
All good things except, I was beat. On Friday, we had 4 total on-track session and I awoke on Saturday AM, full-body sore. Saturday, was a typical day of practice, qualifying and the 1-hour race, of which this time, I was splitting seat time with Olivier. We won the race but I again felt beat, after a 30 minute stint.
The next morning, we only had qualifying in the AM and the main race in the afternoon; not a ton of physical workout time. I qualified P2 and was ready to go for the win during the race. But about 5 laps into the race, my lower back started hurting. Halfway through the race, it was throbbing and I was actively thinking about it during the front and back straightaways. Not a good.
Qualified P2 for the main PRO3 race on Sunday
Long story short, I did not perform anywhere near my full or regular potential and one big reason that I was just not physically fit enough. Here is the race video from the weekend, of which again, isn’t all bad and 1 year ago, I would have been thrilled to finish P3.
But How Did I Do So Well at Pacific?
I’m not entirely sure but I think that while I was in pain during the race, I still had more of my strength, stamina and was also on lots of Ibuprofen, which could have masked some of the pain. At Portland, I think my strength, stamina and reflexes were not at the same level. This variables resulted in a heavier mental toll and it started impacting me even worse.
At the end of the day, it’s not like I really sucked. I still finished on the podium, against a couple of strong drivers that I’ve battled with all year. Jeff McAffer, who overtook me for P2, had a really strong race, with the fastest lap of the race. Olivier and I also won the 1-Hour endurance race!
The main point is that to perform at or near peak levels, you need to be mentally and physically at your peak. I know there are drivers that aren’t into physical fitness and they are solid, if not incredible drivers. They have other strengths, such as functional fitness and years and years of experience. I don’t have more than a few years of racing experience, so I rely on physical fitness as a way to compete.
Moving Forward
For me personally, I am much healthier now and turning my training back up. It will be some time before I’m as physically as fit as before but that is the goal. And if in the future, I am injured, I am going to bite the bullet and rest/heal properly before trying to get back into the cockpit.
This is a combo article because I frankly fell behind righting as the race weekend took over.
Back to PIR to get the bad taste out of my mouth
The last time we were at Portland International Raceways (May 2017), the weekend was going great but on the main points race Sunday afternoon, the race was over by turn 3. A couple of Spec E46’s were tussling ahead, one got pushed off and insisted on getting back on track, immediately spun when the front tires grabbed and got side-swiped. While it sucked for the team, we fared much better than two other PRO3 cars which were nearly totaled.
As an aside, another example of how important it is to know how to properly go off track and apply those techniques, every time – even in racing conditions. The reality is that going off will happen and applying those techniques will save you and everyone else a lot of money in the long run.
That race was run without a chicane (usually reserved for endurance races) and this would be the first of two race weekends with the chicane, aptly named the “Chicane Challenge” and I was really excited to see how the investment in simulator time would pay off.
Friday Test and Tune Day – .5 seconds faster right off the trailer
This isn’t a perfect comparison because of differences in weather conditions but when I looked at my first session off the trailer this Friday versus the same first session, in August 2016 (the last time I ran PIR with a chicane), I was ~.5 seconds faster and broke the 1:30.000 barrier for the second time.
What happened? Softer braking, which lead to higher min-speeds through each corner.
Looking at the data comparison below, it’s clear to see that I was able to use less brake pressure and carry more mid-corner speed AND get on throttle (and full throttle) sooner than a year ago. On this specific session, I remember letting the tires warm up and then attacking the corners and surprising myself that I had so “easily” hit a 1:29.xxx lap time. On the following lap, I tried to repeat it but found that while carrying more speed through the turns 4-5 transition area, the bumps in the road unsettled the car too much while I was on throttle, causing the left rear corner to break loose.
A comparison of my off the trailer, 1st session on a test and tune in August 2016 versus June 2017. Look at the brake pressure differences and the delta chart.
Also, I was driving on relatively old tires (Toyo Proxes RR 225/45/15’s) that were on their third race weekend and their 12th heat cycle. There is an urban legend that PIR “likes old tires” and my personal interpretation is that PIR is a very smooth and grippy track and thus older tires still work well but newer tires are still going to be optimal.
A track map of Portland International Raceways, with a Chicane
The rest of the day I stayed on the old tires and struggled to break 1:30.xxx as the day got hotter and grip went away but we focused on helping that rear left corner take the beating. With PIR being a 12 turn, clockwise track and only 3 of the 12 turns being left handers the car left rear tire is under constant heavy loads, trying to get out of nearly every corner as quickly as possible.
Saturday Qualifying, Points Race 1 and 1-Hour Enduro Race
This was a unique weekend with the Saturday Group 1 race being a championship points race, along with the Sunday race. So each day we would start with a clean slate, qualify in the AM and race in the PM.
First up was Group 1 qualifying, which went ok but I couldn’t find good track position, to get me a solid draft on laps 2-4, where the fastest lap times would come happen. I ended up with a 1:30.092 and qualified 4th. Not bad but not great, being .5 seconds clear of 5th place but almost .7 seconds from pole – ouch.
In Group 8 qualifying, we strapped on some new tires so I could scrub them in for Sunday’s race and boom, 1:29.635! New personal best and, it didn’t seem too hard. The big difference? Carrying a tiny bit more speed into the chicane, more speed into turn 7 and through turns 10-12.
Group 1 Points Race: 3rd Place
At the start of the race, I got a really good start and was behind a the Spec E46 of Dan Rogers, who has a ton of race craft. We were on the inside for turn 1 and more importantly, the outside of turn 2, which is the chicane. On these low speed, high G-force turns, in traffic, it is generally best to be on the outside, because you have less steering input and can get on the throttle sooner. This is because when going two or three wide, we aren’t going at normal speeds, we’re going 10-15 mph slower and thus nowhere near the traction limit.
This gave me a solid run through the chicane and coupled with an incident where another PRO3 car tried to squeeze through where there was no room, spinning both cars – I was in the lead by turn 3 and leading my first PRO3 race?!???!
Leading my first PRO3 race ever, holy crap! Maintain, maintain, maintain….
I lead for a few laps but eventually, Brian Bercovitz got me and pulled away. Then the PRO3 who spun the other car, caught up and when we were going around slower traffic, he got a clean run out of a corner while I had to check up and he got past. I ended up in P3 but further improved my personal fastest lap time.
Group 8 1-Hour Race: 2nd place for being greedy
The 1-hour races are basically more practice for me – I like doing them by myself because I can just focus on hammering out laps and hard-coding improvements. I always strap on the oldest tires I have on-hand and try to set fast and consistent laps.
This was no different and from the start I was battling with a regular foe and friend, Jeff McAffer. I was in the lead the majority of the race but Jeff was able to stick with me the entire time.
After the mid-way pit stop, I decided to try to push a bit more as I was hitting 1:29 lap times, on crappy tires and a greasy track. Suddenly, 1:29.7xx! I felt like that lap time wasn’t too hard to get, so I went for a repeat but the tires didn’t agree.
This could have easily been just my inputs but my hypothesis is that I over-pushed the tires and I was asking them to do a qualifying lap when they were in lap 35 of a race. I had the win in the bag and Jeff about 5 seconds behind but I got greedy, went off and ended up in P2.
This is not a good POV at turn 12 at Portland International Raceways
Now I know there is a reason for the saying…
“Go only as fast as you need to finish where you’re going to finish.”
Sunday Group 1 Race
One thing that I started doing this year is running just Group 1 and Group 8, which means I get a solid amount of track time and on Sunday, I only have one group to worry about. This way I’m rested and not rushing on the day that usually counts.
Sunday Group 1 Qualifying: 1:29.874 P4
Coming off of the Saturday’s lap times, where I got a 1:29.466 in the afternoon Group 1 race, with fresh tires but loaded up on weight for race trim, I felt that I had the potential for a very low 1:29 in qualifying and thus in the running for pole. I just needed to have good track position on laps 2-4, where I could get a draft on at least one of the straightaways. But it wasn’t to be – I went out and was stuck in “no man’s land” for the first part, then I slowed down and waited for a group of PRO3 cars to come by so I can get behind them. I was able to finally do so and had a low 1:29 going but got behind a PRO3 car that slowed down way too much for turns 10 – 12. It was still good enough for a P3 but I knew I had the pace to battle for the podium and possibly the win. If I would have had an average sector time for turns 10 – 12, I would have been easily with a 1:29.4xx with my rolling best lap being a 1:29.522.
Purple cells = rolling fastest lap and yellow cells = fastest segment times
Sunday Group 1 Race: P7 finish due to a late race off-track excursion
The race started well and hard for most everyone, with a clean first lap. I tried hard to make up at least one spot on the start but it didn’t happen, so I was stuck behind the #81 of Brad McAllister, who is a strong driver and PIR is one of his strongest tracks. He’s also a pretty tough pass, with a strong racing history in the SCCA Playboy MX-5 Cup, PRO3 and recently the TRANS-AM TA2 series.
Brian Bercovitz, one of the regular competitors I’m trying to best started from the back because he had a mechanical during qualifying and eventually caught up to us. The couple laps leading to Brian catching us, I had to brake harder than normal to not ram Brad going into the chicane, which over-heated (I think) my front tires. Going into turns 5 and 6, my front end washed out, and as I was waiting for the fronts to grip, the rear-end swung out and I went-off track.
It was not too bad but just enough time for a couple cars to pass me and by then the tires were too hot and the distance too great for me to catch up and make up the spots.
I ended up finishing 7th and I think if we can do a better job of tire pressure management (to give me more life towards the end of the race) and I can do a better job of not screwing up, there was a 3rd place finish in the stars and maybe better.
Overall, a great weekend and new personal bests!
While I’m not terribly happy with the Sunday result, overall we made a ton of progress on the car and my driving. There is one more race at PIR with a Chicane in August and I believe we’ve gathered the knowledge to fight for poles and a win. We know what we can do to drop some low 1:29’s and maybe even get into the 1:28’s, which is encroaching on track record territory. Let’s cross our fingers for some sunny and not too hot, weather in August!
As I mentioned yesterday, today was the first official day of the race weekend, with four sessions on the schedule:
Group 1 Qualifying
Group 8 Qualifying
Group 1 Non-Points Sprint Race: ~20 minute race with results not counting towards the PRO 3 championship but your fastest lap counting towards the final qualifying grid)
Group 8 Race: 1 Hour mini-endurance race that counts towards the 2017 Mini-Endurance championship (I’ve won the championship the last two years in a row!)
Yesterday, I felt like I had established a new level of performance with the car and my driving, by improving my personal best lap time at Pacific Raceways by nearly .5 seconds and being able to repeat it, though in just one lap, with a set of brand new tires on a ‘heat cycle’ run.
Today, my goal was to take those new tires, and do a qualifying run in them for Group 1, improve on my personal best lap time and then put them away until Sunday. Then swap back on the older set of tires, which would be going on their 10 – 12th heat cycles and while still good from a tread standpoint, I fully expected the performance to start wearing off towards the end of the 1 hour endurance race.
How’d it go?
Group 1 AM Qualifying
Time of Day: 9:26 AM
Conditions: Mostly sunny, 61 degrees Fahrenheit
Result: 1:37.617 (new personal best by ~.2 seconds)
Similar issue as I had during qualifying for Group 1 in Portland but I didn’t position myself best in the pack during pre-grid. I got out early in the line up and while I was at the front, I didn’t have the benefit of a draft like when running in a pack. I did about 4 laps but not cracking the 1:38 barrier. So I decided to back off a bit and get behind a pack of PRO3 cars to catch their draft. After a couple laps, I was able to get a 1:37.766 but then was too close to them and basically started ‘racing’, so I tried to back off a little before the start of a lap and then make a run but I’d get too close about halfway through the lap and the lap would get ruined. Either way, minor improvement and felt like I at least collected enough data of several low 1:38’s, which used to be my personal best and figure out what to do.
Group 8 (Mini Enduro) AM Qualifying
Time of Day: 11:30 AM
Conditions: Mostly sunny, 68 degrees Fahrenheit
Result: 1:37.533 (new personal best by ~.1 seconds)
With the field being lighter for Group 8, track position wasn’t as important, so I just went out and tried to put down fast laps immediately after doing more of a warm up lap on my out-lap. Since these were the old tires, we were trying to make sure we’d get them up to temperature and pressures for the race in the afternoon. I did two fast laps of 1:37.855 and then 1:37.533. BOOM! Another personal best. What was I doing? Just focusing on having next to no transition period from ending trail-braking to throttle application, especially on the longer corners like turn 2 and turn 8. I came in to the hot-pits for a pressure and tire temp check and was out but was only able to put down a 1:37.792. The good news? 1:37’s were starting to feel like the new normal!
Group 1 – 20 Minute Non-Points Race
Time of Day: 1:50 PM
Conditions: Mostly sunny, 75 degrees Fahrenheit
Result: 2nd place finish and 1:37.258 (new personal best by ~.3 seconds)
These races are interesting. It’s racing but it doesn’t count towards point, so this year they changed it so that the laps count towards qualifying. So, you should never try to win at all costs but the goal is more to get into a flow and go for some fast laps. I qualified 4th but started third in class, because the pole setting car decided to start from the back OR they were late to grid. Either way, my goal was the same – get a good start and stick my front bumper to the rear-bumper of the fastest PRO3 this year, Brian B in the Blaupunkt liveried car.
And that’s what happened! Man, I am so happy about how this race went (video link below soon). I knew at least at the time that I would have to work really hard to get the start I wanted and then work even harder/smarter to stick with Brian. I pushed myself even more to be on maintenance, plus a little more, sometimes mid-corner and I found myself using throttle to get that final phase of rotation going in the slower corners of 3a and 3b.
2nd Place and a new personal best lap time!
The best thing? Mid 1:37’s became the new normal, even in greasier but not horrible conditions.
Group 8 – 1 Hour Endurance Race
Time of Day: 4:30 PM
Conditions: Sunny, 78 degrees Fahrenheit
Result: 1st Place finish and 1:37.364 (only .1 seconds off of personal best)
The fields aren’t typically super-stacked for the endurance races, usually only about 10-15 cars per class and with the SCCA Majors Tour happening in Portland this weekend, the overall field was much lower, with only about 19 or so total cars on the grid. There would only be one strong competitor battling me, Jeff M in the newly painted green and black #24. Jeff and I have shared many battles the last couple of years and he and his car are a rocket. With tires nearing the end of their top end performance life, my goal was to just drive clean, consistent laps and hopefully win but not do anything stupid.
Enduro’s are an opportunity for more seat time for me, in a racing environment and over a long period of time to try different things. I also like that one mistake won’t kill you and there is a strategy aspect to the race.
In the end, Jeff and I traded spots a couple times. I was able to get him in the beginning and get in front but a mistake in turn 8 gave him the position back and I had to work to get it back. After the mandatory pit-stop, I was able to get him back but due to traffic, worsening track conditions and his driving, I wasn’t able to pull away. Aside from winning, what I am incredibly happy about is being able to put down a 1:37.364 in the second half of the race! Man, I am so happy about that.
1st Place and almost matching my personal best!
Takeaways? A new normal and 1:36’s – here I come!
Today was an absolutely awesome day and from a driving standpoint, I believe the reason is that I have fresh in my body and mind, what it feels like to drive, look at data, see what to do differently, visualize what that looks like and make it happen. I will create a separate post that looks only at the data analysis I did over the whole weekend and what I did to prepare myself to do things differently.
The last thing here, especially from the lap times from the endurance race, if I am getting near my personal best lap times on a nearly 80 degree day, in the second half of a 1-hour race and on 11 heat cycle tires, that means this car is capable of so much more. If the driver can get it together or with a pro-level driver behind the wheel, today, this car could have probably turned a low 1:36.xxx. Lots of progress but so much more to go!
What: First sprint race weekend of the year, shaking down the car with new upgrades, testing and experiencing the highs and lows of racing.
If I knew then, what I know now:
Make no assumptions on communication! Make sure everyone on your team knows exactly what is happening and when. We lost a day to shake down the car and found an obscure issue with the new transmission resulting in more lost track time on Saturday.
Make sure you know what kind of qualifying is happening, open session or pressure style and adjust tire pressures accordingly.
Plan where you want to be on pre-grid for open session qualifying wisely so that you can benefit from drafting other cars in class and even faster cars.
As I mentioned the 6 Hours on the Ridge post, I primarily race with ICSCC, which is a sprint race focused sanctioning body. Aside from the endurance races that bookend the start and end of the season, each race weekend is made up of the following elements (for the most part):
Friday test and tune – usually for race cars only but sometimes includes High Performance Driver Education (HPDE drivers).
Saturday – Practice, qualifying, non-points races and a 1 hour endurance race.
Sunday – Final qualifying and points races
Here is a picture of the announcement for the race weekend of which if you do a couple of groups, that is plenty of track time. This weekend and for the full year, I did Group 1 (the main group for the PRO3 annual championship) and the Mini-Enduro.
The schedule for the first sprint race of the season. I’m in Group 1.
Shaking down a refreshed car
Initially I was supposed to get the #209 Track Attack PRO3 car back from Advanced Auto Fabrications at the 6 hour race but when they were doing final checks on it, they found that the newly rebuilt transmission wouldn’t go into third gear. So we decided to have that fixed and bring it down for this weekend, where I would shake the car down and ‘take delivery’ from all the repairs and upgrades they did.
What I did not make explicitly clear was that I expected AAF and crew to be there on Friday, which they would do more often than not, but not always. I even checked in the Monday prior to make sure all was on schedule but I did not explicitly ask about Friday.
Big mistake because when we drove down on Thursday night, so we could be all unloaded and ready to drive on Friday AM, the gigantic black AAF hauler was nowhere to be seen. AAF and crew decided to skip the test and tune due to the limited amount of track time and forecasted rain in the morning. They’re not scared of rain, just that if it isn’t supposed to rain on Saturday or Sunday, the risk of damage is higher than the benefit.
Regardless, we made the most of the day by working on odds and ends in the RV, spend some quality time with the family, caught up on work and chatted with folks up and down the paddock. The AAF crew showed up on Friday evening and by Saturday AM, was all set for the first on-track session.
As I got going in the morning practice run, it took me a few laps to get into the groove of things, remember the course and get up to speed. Initially letting several cars pass me but then quickly catching and passing them again. Lap times were solid, with nearly a .8 second improvement from the year prior. SWEET!
When we came off the track, a fellow PRO3 driver mentioned that they saw smoke coming out of the back of my car, a light smoke but consistent. We checked the car and sure enough, the rear and under body was coated with transmission oil. We were leaking somewhere from this newly rebuilt transmission that aside from this, seemed to be running great.
That is transmission oil – note that it is everywhere.
Over the next several hours, we went step by step, replacing the main rear transfer seal and then the shifter seal. We thought we had it addressed but after the non-points race, still had oil.
Long story short, it turns out that when the transmission was sent for a rebuild, they took my old transmission in as a core and sent back a different transmission, from an older model of the E30, which had a different kind of shift mount assembly. This assembly had two bolts that mounted to the top of the transmission, which served the purpose of securing the assembly and sealing two bolt holes into the transmission itself.
We don’t run the OEM shifter assembly, opting instead for the incredibly awesome CAE shifter assembly, which meant those holes were completely exposed and the source of the leak. This obscure situation had never come up with this crew of people who have been racing E30’s for over 10 years and built and rebuilt dozens of PRO3 cars.
We didn’t figure this out until Saturday early evening, after we opted to not run the 1 hour endurance race, to save the transmission (if it kept leaking) for the Group 1 qualifying and racing on Sunday. We felt the risk was too high to run low on transmission oil in the 1 hour and potentially damage the transmission itself.
In conclusion, lack of communication and shaking down the car resulted in a completely lost Friday of running and 1 hour of endurance racing. Sigh.
Qualifying
For the weekend, we had two qualifying sessions, one for the 1 hour endurance race and qualifying times for the Group 1 race.
1 Hour endurance race pressure qualy
Something unique to the Cascade Sports Car Club, which I love is pressure qualifying. One out lap, one flying lap and one in lap. Unfortunately, we did not realize this until we got to grid and didn’t adjust the tire pressures accordingly to compensate for the much fewer laps we’d run. At least everyone else was in the same boat. I love this type of qualifying because it eliminates the ‘draft’ variable – this is all on you as a driver, to make a fast lap happen there and then. Not relying on getting a draft from a faster car or following and learning from a faster driver. At a track like PIR, especially with no chicane on the front straight, a draft can make a HUGE difference, in the order of .25 seconds or more if you can get the right draft on the front and back straights.
Here is the video of my ME2 qualifying lap, which put me on pole for ME2 class but was a solid one second slower than my fastest laps in a regular qualifying session.
Group 1 qualy
Qualifying for Group 1 was spread across the fastest lap times in the Saturday non-points race and Sunday AM qualifying. The fastest time across those two sessions would count towards the final grid placement.
In the Saturday AM race, I qualified 4th with a mid-1:22 lap time and finished the race in 3rd. It was an excellent race, where I got a great start and was running in 2nd before turn 2 of the first lap. I tried to hitch myself to Brian Bercovitz, the eventual race winner but he got away and was stuck battling with Corey Peters for 2nd place. I ran in 2nd for about half of the race but I ended up going too hot into turn 1, went wide and that was enough of a mistake for Corey to capitalize. That meant Kyle Byers in the #55 PRO3 car was on my tail. We ended up battling pretty hard, exchanging some bumper paint but nothing serious – just good, solid, respectful, hard racing. He ended up getting a little sideways on the second bump he gave me and that was enough for me to pull away and finish in third, with a lap time of 1:22.274 and a new personal best.
Sprint non-points race results and qualifying 1 times
I would normally post the video here but I forgot to hit ‘record’ – I’ll try to get the videos from Corey and Kyle to share.
Sunday AM qualy brought out excellent conditions; dry, sunny and a cool breeze in the low 60’s. I got on the grid early and was the lead PRO3 car on track but after a few laps, I realized I was reproducing low 1:22 lap times while everyone else was running in a pack and getting help with drafts. So I came into the hot pits, checked tire pressures and waited for the right pack to come by and tail them.
I eventually got behind the pack with Corey Peters coming off of the back straight but he quickly picked up on my game and pulled off on the main straight away. No issues, there was still another couple of cars to get behind. On a decent flyer though, another driver, who I used for a draft and got by on turn 1 decided it was time to race and dove in to overtake in turn 7. Why?!?!?! What makes this more frustrating is that he then pulled off and slowed down that same lap, in the following straight away. I can’t confirm but I think he also picked up on what I was planning and decided to ruin my lap.
No issues again and finally, I saw Brian Bercovitz and got behind him for one last final flying lap. All looked good, with the predictive lap timer showing a 1:21.8xx for the first part of the lap but then I missed a downshift to third on the only left hand turn on the course. This ended up still producing a solid lap time but I ended up qualifying in 5th place, where as if I would have executed, I would have qualified third and possibly 2nd in class.
The Main Race
The goal was simple: get a solid start, make up a couple positions in the traffic and be in the top three by the end of lap 1. This would give me a fighting chance to get near the front and try to stick with Brian, who was on pole for our class. I found during qualifying that if I could get behind him, I was able to keep the gap nearly the same.
Below is the race video and note, it has no data overlay. The reason? I didn’t complete a single lap. I got a solid start and wedged myself in a position to go after 2nd, 3rd and possibly first by turn 7. Unfortunately, up ahead, a Spec E46 car went off to the left and tried to get themselves back on the track without waiting for the pack to go by (my opinion). When his front tires, who were turned to the right, hooked up on the track surface, they gripped and shot him across the track and into the on-coming pack of angry PRO3 cars.
I saw it happening, moved to the right but still got a glancing blow on the rear quarter panel. Initially I thought all was well because it didn’t really knock me anywhere but as soon as we hit turn 7 (right hand turn leading to the back straight), I saw and heard heavy tire rub and then the cabin was engulfed in tire smoke. I went into the hot pits, got checked for fire but the damage was too much. We could have swapped tires and rolled the fender in the hot-pit but we would have gone a couple laps down and I didn’t think it was worth it and called it a day.
Conclusion
It was a tough way to start the sprint season but when you sign up to go racing, this is a potential outcome that can happen any weekend. I take 100% accountability for what happened and don’t blame the Spec E46 driver in any way. All things considered, had a great time with friends and family, personal best lap times, fixed teething issues on the car and was still able to take it home, running and with some cosmetic repairs needed before the next race. There were three other cars involved in the incident and they would take my place in an instant as their cars did not fair as well.
Damaged driver side quarter panel and hard rubbing on tire.The guys using a jack bar to roll the fender so the tire could clear.
